The TN2252 is a perfect pairing of the TN226 amplifier with a two EDEN-designed 10" speakers. The TN2252 is a great gig worthy combo equally suited rehearsals as well as having a great Di out for when you need to use the front of house system.
|Speaker Config:||2 x 10"|
|EQ Control:||4-band EQ with semi parametric mid controls, Enhance control & Bass Boost|
|Dimensions:||H: 15.9 in / 40.5 cm
W: 22.8 in / 58 cm
D: 15.9 in / 40.5 cm
|Weight:||49.3 lbs / 22.4 kg|
TN2252 Front View
TN2252 Angled View
TN2252 Angled View
TN2252 Back View
Roll over parts of the product to find out more.
Designed by Eden, this speaker is made specifically for Eden cabinets.
The TN2252 features two punchy 10" drivers.
Inputs, Volume and EQ controls are found on the top of the combo.
Outputs are found on the back of the combo.
The Eden Logo
Bass players know when they see this on your cabinet that you truly care about your tone.
This high fidelity tweeter extends your bass's high end to ensure you cut through the mix.
Years of listening and testing have resulted in these perfectly tuned ports which provide the optimal amount of air flow for clean, clear lows.
Active Instrument Input
Plug your active or high output bass in here.
Enhance Control, Switch & Indicator
This EQ sweep allows quick and effective adjustment of your EQ with a single dial. For best results use the Enhance control with all other EQ settings at 12 O’clock before detailing your tone.
Input Gain Control & Clip Light
Use this control to adjust the amount of signal sent into the preamp stage. Use in conjunction with the Input Gain clip light to avoid clipping the input stage of the amplifier.
Adjust the low frequencies of the amplifier using this control.
Low Mid Control
Change the amount of frequency adjustment by the low mid freq sweep using this dial.
Adjust the highest frequencies on the amplifier using this control.
Master Volume Control
Control the overall volume of your amplifier.
Passive Instrument Input
Plug your passive or low output bass in here.
Hi Mid Control
Change the amount of frequency adjustment by the hi mid freq sweep using this dial.
Mute Switch and Indicator
Use this switch to mute and un-mute the amplifier. When the amplifier is muted the light will illuminate.
Compressor Switch and Indicator
Use this switch to turn the built in compressor circuit off and on. This LED will illuminate when the compressor feature is switched on.
Bass Boost Switch & Indicator
Use this switch to turn on the Bass boost feature on the amplifier. When engaged the Bass control will provide more pronounced Bass adjustment.
Low Mid Freq Sweep
Adjust the frequency affected by the Low Mid control from 30 Hz up to 300 Hz using this control.
Hi Mid Freq Sweep
Adjust the frequency affected by the Hi Mid control from 200 Hz up to 2000 Hz using this control.
EQ Clip Indicator
When illuminated this LED indicates the EQ stage of the amplifier is causing the amp to clip. To avoid clipping adjust the frequency controls until the light remains off.
Illuminated EDEN Logo
Lights up when unit is switched on.
Send your signal to an external tuner.
Send/return your signal to use external effects.
Connect your phone, MP3 player or other device here.
Plug in your headphones here for silent practice.
Turn the combo on and off using this switch.
External Speaker Output
Connect a separate speaker cabinet using a 1/4" jack cable and disengage the internal speaker.
Observe the minimum load limit for the amplifier.
Accepts standard XLR equipped mic cable for output to a recording console or front of house PA.
With Pre/Post selection, DI Out Level and Ground Lift.
Choose to take the DI signal from either before or after the preamp shaping circuit inside the amplifier.
DI Out Level
DI Pad: Pad the signal (reduce the output level) between line level and mic level using this switch.
DI Ground Lift
Lift ground from your signal (when required) using this switch.
Plug in the optional Terra Nova footswitch here.
Plug in your Eden-supplied power cable here.
Back to top